Saturday, 21 November 2026

Ohm's law Simulator

⚡ OHM'S LAW – VIRTUAL PHYSICS LABORATORY

Explore voltage, current and resistance through an interactive electrical experiment.

Learn • Connect • Experiment • Observe • Discover

📚 Interactive Index

Click any topic to navigate to that section. Click the audio button to listen to the explanation.

1. Aim and Objectives

Aim: To study the relationship between potential difference and electric current flowing through a conductor and to verify Ohm's law.

Learning objectives

  • Understand potential difference, electric current and resistance.
  • Connect an ammeter in series and a voltmeter in parallel.
  • Observe changes in current when voltage or resistance changes.
  • Plot a voltage-current graph.
  • Calculate the resistance of a conductor.

2. Theory – Ohm's Law

Ohm's law states that the electric current flowing through a conductor is directly proportional to the potential difference across its ends, provided its temperature and other physical conditions remain constant.

V ∝ I   or   V = IR

V – Potential Difference

Measured in volts (V). It is the energy supplied per unit charge between two points.

I – Electric Current

Measured in amperes (A). It is the rate of flow of electric charge.

R – Resistance

Measured in ohms (Ω). It is the opposition offered by a conductor to electric current.

Mathematical forms

V = IR
I = V/R
R = V/I

Important: If resistance remains constant, doubling the voltage doubles the current. If voltage remains constant, doubling the resistance halves the current.

3. Apparatus Required

Click each apparatus to learn its construction, function, connection and application.

🔋 Battery / DC Supply

Provides electrical energy to the circuit.

🔌 Ammeter

Measures electric current in amperes.

📟 Voltmeter

Measures potential difference in volts.

▰ Resistor

Provides resistance in the circuit.

🔑 Plug Key

Opens or closes the circuit.

🔘 Tap Key

Momentarily makes electrical contact.

🔋 Electric Cell

Single electrochemical source.

🔗 Connecting Wires

Complete the electrical path.

🎚 Rheostat

Varies resistance and current.

🧰 Resistance Box

Provides known resistance values.

4. Interactive Circuit Diagram

Click any component in the diagram to hear its explanation. The green line represents a closed circuit and the grey dashed line represents an open circuit.

Battery Plug key A Ammeter Resistor V Voltmeter Schematic representation – virtual educational circuit
Connection rule: Ammeter – series connection. Voltmeter – parallel connection across the resistor. Connecting an ammeter directly across a battery can cause a short circuit.

5. How to Connect the Apparatus

Series connection

Battery positive terminal → plug key → ammeter → resistor → battery negative terminal.

All these components carry the same current.

Parallel connection

Connect the voltmeter's positive terminal to one end of the resistor and its negative terminal to the other end.

It measures the potential difference across the resistor.

Step-by-step connection guide

  1. Connect the positive terminal of the battery to the plug key.
  2. Connect the plug key to the positive terminal of the ammeter.
  3. Connect the negative terminal of the ammeter to the resistor.
  4. Connect the other end of the resistor to the negative terminal of the battery.
  5. Connect the voltmeter across the two ends of the resistor.
  6. Check the positive and negative polarities before closing the key.

6. Live Virtual Experiment

Experiment mode: Adjust the voltage and resistance. Close the key to observe the real-time current and voltage readings. The simulation uses Ohm's law to calculate the values instantly.

⚡ Battery Voltage

Adjust the potential difference supplied by the battery.

▰ Resistance

Adjust the resistance of the resistor.

🔑 Control the circuit

Circuit status: OPEN – No current flows.

VOLTMETER – Potential Difference0.00 VConnected in parallel
AMMETER – Electric Current0.00 AConnected in series
RESISTANCE10 ΩResistor value
POWER0.00 WElectrical power consumed

Mathematical calculation

I = V / R = 0 / 10 = 0 A

Close the plug key to start the experiment.

Try these activities:
  • Keep resistance constant and increase voltage. Observe the current.
  • Keep voltage constant and increase resistance. Observe the current.
  • Close and open the plug key and observe the change.
  • Use the tap key to allow current for a short time.

7. Ammeter and Voltmeter – Detailed Study

🔌 Ammeter

  • Measures electric current.
  • SI unit: ampere (A).
  • Connected in series.
  • Has very low internal resistance.
  • Used to measure current in electrical circuits.

📟 Voltmeter

  • Measures potential difference.
  • SI unit: volt (V).
  • Connected in parallel.
  • Has very high internal resistance.
  • Used to measure voltage across electrical components.

Comparison

FeatureAmmeterVoltmeter
MeasuresCurrentPotential difference
UnitAmpereVolt
ConnectionSeriesParallel
Ideal resistanceZeroInfinite
SymbolA in a circleV in a circle

8. Electric Cell and Battery

Electric Cell

An electric cell is a source of electrical energy. It converts chemical energy into electrical energy.

It has two terminals: positive and negative.

Example: A 1.5 V dry cell.

Battery

A battery is an arrangement of one or more electric cells connected together.

Cells connected in series increase the total voltage when connected in the same direction.

Cell versus Battery

CellBattery
One electrochemical unitOne or more cells
Supplies electrical energySupplies electrical energy
Example: single dry cellExample: car battery

9. Plug Key and Tap Key

Plug Key

A plug key is a switch used to make or break a circuit by inserting or removing a conducting plug.

Uses: Controlling current during school laboratory experiments.

Tap Key

A tap key is a momentary switch that makes contact when pressed or tapped and breaks contact when released.

Uses: Short-duration electrical contact in experimental setups and signalling circuits.

10. Resistors – Types and Uses

Fixed Resistor

Provides a constant resistance value.

Variable Resistor

Resistance can be changed manually.

Resistor Uses

Current control, voltage division and protection of electronic components.

Resistance Unit

Ohm (Ω), named after Georg Simon Ohm.

11. Observation Table

Perform readings with the key closed. Add the current experimental reading to the observation table.

S.No.Voltage (V)Current (A)Resistance (Ω)V/I (Ω)
No readings recorded yet.

12. Voltage versus Current Graph

Observe the graph as you change voltage and resistance in the experiment. The horizontal axis represents current and the vertical axis represents voltage.

Close the key to see the graph.

13. Verification of Ohm's Law

For a conductor maintained at constant temperature, calculate V divided by I for different observations.

R = V / I = Constant

Take readings to verify the relationship.

14. Resistors in Series and Parallel

Series Combination

Resistors are connected one after another in a single path.

R = R₁ + R₂

Equivalent resistance is greater than either individual resistance.

Parallel Combination

Resistors are connected across the same two points.

1/R = 1/R₁ + 1/R₂

Equivalent resistance is less than the smallest individual resistance.

15. Limitations of Ohm's Law

Ohm's law is not universally applicable to every electrical device or material.

  1. Temperature changes: Resistance may change when the temperature of the conductor changes.
  2. Non-ohmic materials: Some materials do not show a linear relationship between voltage and current.
  3. Semiconductor devices: Diodes and transistors do not generally obey a simple linear V-I relationship.
  4. Electrolytes: Current-voltage behaviour in electrolytes may be nonlinear.
  5. Gas discharge devices: Discharge tubes and gas-filled lamps have nonlinear characteristics.
  6. Special conditions: Certain materials under unusual physical conditions do not obey the simple law.
Remember: Ohm's law applies when the physical conditions, especially temperature, remain constant and the conductor exhibits an ohmic relationship.

16. Applications of Ohm's Law

Calculating current in electrical circuits.
Determining the resistance of a conductor.
Designing electrical and electronic circuits.
Selecting suitable resistors.
Troubleshooting electrical equipment.
Understanding voltage drops in circuits.

17. Laboratory Precautions

  • Use only a low-voltage DC supply for the school experiment.
  • Never connect an ammeter directly across the battery.
  • Always connect the voltmeter in parallel.
  • Observe correct positive and negative terminal connections.
  • Keep the plug key open while making connections.
  • Close the key only while taking readings.
  • Avoid overheating the resistor.
  • Use suitable meter ranges and do not exceed their ratings.
Safety: This is a virtual educational simulation. For a physical experiment, use an approved low-voltage laboratory supply under teacher supervision. Never use household mains electricity.

18. Student Assessment – Test Your Knowledge

Select the correct answer for each question and click Submit.

Your score will appear here.

0 comments:

Post a Comment